13.3英寸TFT液晶显示屏 TN型 1366*768分辨率 亮度200 高清数码屏

13.3英寸TFT液晶显示屏
GENERAL DEION
1.1 Introduction
HB133WX1-201 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 13.3 inch
diagonally measured active area with HD resolutions (1366 horizontal by 768 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical Stripe and this module can display 262K colors. The TFT-LCD panel used for this
module is a low reflection and higher color type. Therefore, this module is suitable for
Notebook PC. The LED Driver for back-light driving is built in this model.
All input **s are EDP1.2 interface compatible.
1.2 Features
?1 lane EDP1.2 interface
?Thin and light weight
?6-bit color depth, display 262K colors
?Single LED lighting bar. (Down side/Horizontal direction)
?Data enable ** mode
?Up/Down mounting frame
?Green product (ROHS & Halogen free product)
?On board LED driving circuit
?Low driving voltage and low power consumption
?On board EDID and Timing integrated into one chip
1.3 Application
?Notebook PC (Wide type)
1.4 General Specification
The followings are general specifications at the model HB133WX1-201 (listed in Table 1.)
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
4.0 OPTICAL SPECIFICATION
4.1 Overview
The test of optical specifications shall be measured in a dark room (ambient luminance ? 1
lux and temperature = 25?2℃) with the equipment of luminance meter system (Goniometer
system and TOPCON BM-5) and test unit shall be located at an approximate distance
50cm from the LCD surface at a viewing angle of θ and Φ equal to 0?. We refer to θ?=0
(=θ3 ) as the 3 o’clock direction (the “right”), θ?=90 (= θ12 ) as the 12 o’clock direction
(“upward”), θ?=180 (= θ9 ) as the 9 o’clock direction (“left”) and
θ?=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or ?, the center
of the measuring spot on the display surface shall stay fixed. The backlight should be
operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25?C.
Optimum viewing angle direction is 6 ’clock.
5.0 INTERFACE CONNECTION.
5.1 Electrical Interface Connection
The electronics interface connector is STM or Compatible or equivalent. The mating connector part number is I-PEX 20454-030T or Compatible. The connector interface pin assignments are listed in Table 6.
9.0 Connector Deion
Physical interface is described as for the connector on LCM.
These connectors are capable of accommodating the following **s and will be following components.
10.0 MECHANICAL CHARACTERISTICS
10.1 Dimensional Requirements
FIGURE 6 shows mechanical outlines for the model HB133WX1-201.
Other parameters are shown in Table 9.
10.2 Mounting
See FIGURE 6.
10.3 Glare and Polarizer Hardness.
The surface of the LCD has an hazed coating to achieve anti-glare effect and hard coating
to reduce scratching.
10.4 Light Leakage
There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of
350lux.
12.0 HANDLING & CAUTIONS
(1) Cautions when taking out the module
? Pick the pouch only, when taking out module from a shipping package.
(2) Cautions for handling the module
? As the electrostatic discharges may break the LCD module, handle the LCD module with
care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
? As the LCD panel and back - light element are made from fragile glass material, impulse
and pressure to the LCD module should be avoided.
? As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth
without chemicals for cleaning.
? Do not pull the interface connector in or out while the LCD module is operating.
? Put the module display side down on a flat horizontal plane.
? Handle connectors and cables with care.
(3) Cautions for the operation
? When the module is operating, do not lose CLK, ENAB **s. If any one of these
**s is lost, the LCD panel would be damaged.
? Obey the supply voltage sequence. If wrong sequence is applied, the module
would be damaged.
(4) Cautions for the atmosphere
? Dew drop atmosphere should be avoided.
? Do not store and/or operate the LCD module in a high temperature and/or humidity
atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively
low temperature atmosphere is recommended.
(5) Cautions for the module characteristics
? Do not apply fixed pattern data ** to the LCD module at product aging.
? Applying fixed pattern for a long time may cause image sticking.
(6) Other cautions
? Do not disassemble and/or re-assemble LCD module.
? Do not re-adjust variable resistor or switch etc.
? When returning the module for repair or etc., Please pack the module not to be broken.
We recommend to use the original shipping packages.